Tempco TEC-2500 Скачать руководство пользователя страница 68

Страница: 68 / 108

4–6 Differential Control

In certain applications it is desirable to control a second process such that its process

value always deviates from the first process by a constant value. To achieve this, set the

following parameters in the setup menu.

FUNC=FULL

IN1, IN1L, IN1H are set according to input 1 signal

IN2, IN2L, IN2H are set according to input 2 signal

IN1U, DP1, IN2U, DP2, are set according to input 1 and input 2 signal

PVMD=P1-2 or P2-1

SPMD=SP1.2

The response of PV2 will be parallel to PV1 as shown in the following diagram

The PV display will indicate PV1-PV2 value if P1-2 is chosen for PVMD, or PV2-PV1

value if P2-1 is chosen for PVMD. If you need PV1 or PV2 to be displayed instead of PV,

you can use the display mode to select PV1 or PV2 to be viewed. See section 3-24.

Error messages

If P1-2 or P2-1 is selected for PVMD, while PV1 or PV2 is selected for SPMD, an

error code will appear.

In this case the signals used for input 1 and input 2 should be the same unit and the

same decimal point, that is, IN1U=IN2U, DP1=DP2, otherwise an error code will

appear.

Setup

PVMD=P1-2

or PVMD=P2-1

SPMD=SP1.2

Error message

Содержание TEC-2500













































































































Результаты поиска

Содержание TEC-2500

Отзывы:

Tempco TEC-2500, Инструкция по эксплуатации, Страница: 68 / 108

Результаты поиска

Содержание TEC-2500

Отзывы: