Teledyne LabMaster 10 Zi Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 235

Teledyne LabMaster 10 Zi Series Скачать руководство пользователя страница 49

LabMaster 10 Zi Oscilloscopes

42

LM10Zi-GSM-E Rev A

Probes

Teledyne LeCroy offers a variety probes for use with your oscillocope.
The types compatible with the LabMaster 10 Zi are listed below. Visit
teledynelecroy.com for specifications and ordering information.



Single-Ended

- A single-ended, active probe is associated with

measuring voltages at high frequencies. Measurement with an
active probe requires a test point and a ground point. The ground
(also called earth) acts as a zero reference for the test point
measurement. These probes are typically low-bandwidth and
require an adapter to connect to the 2.92 mm and 1.85 mm
interfaces on the 10-xxZi Acquisition Modules.



Differential Probes

- Differential active probes are like two

probes in one. Instead of measuring a test point in relation to a
ground point (like single-ended active probes), differential probes
measure the difference in voltage of a test point in relation to
another test point. Some models of differential probes may
require an adapter to connect to the 2.92 mm and 1.85 mm
interfaces on the 10-xxZi Acquisition Modules.

Connecting to 1.85 mm Probe Interfaces

Teledyne LeCroy's LabMaster 10 Zi oscilloscopes utilize a 1.85mm probe
interface for inputs up to 65 GHz. This interface consists of a precision
female connector with a male-male barrel adapter and a LEMO power
and communication connector. It offers 50 Ω input impedance only.

For additional connection interface information, refer to

Dual Channel

Acquisition

in the online help.

The 1.85 mm high-bandwidth electrical paths are comprised of two
items – the precision female connector and a male-male barrel adapter.

The female connector is mounted into the oscilloscope connector panel.
It is a low-loss connector that is designed for frequent
connect/disconnects.

«
...
47
48
49
50
51
...
»

Содержание LabMaster 10 Zi Series












































































































































































































































Отзывы:

Нет отзывов