Teledyne LabMaster 10 Zi Series Скачать руководство пользователя страница 176 | Manualshive

Страница: 176 / 235

Teledyne LabMaster 10 Zi Series Скачать руководство пользователя страница 176

Getting Started Guide

LM10Zi-GSM-E Rev A

169

Flashback Recall

With a stored entry selected on the

My Notebook Entries

section of the

dialog, touch the

Flashback (Recall)

button to return your instrument to

the state it was in when the Notebook Entry was saved.

Exit Flashback by touching the

Undo Flashback

button in the top-right

corner of the screen, or the

Auto Trigger

front panel control.

PLEASE NOTE THE FOLLOWING

: The flashback feature currently recalls

the oscilloscope Setup, and all displayed waveforms. Some of result
data is not recalled, including:



Persistence data

- While it is saved in hardcopy and is printed on

the report, it is not recalled during Flashback.



Histogram data

- Histograms internally have a 32-bit resolution,

but when stored into a trace file and recalled during flashback
they are clipped to 16-bits.



Floating point waveforms

- Certain math operations result in the

creation of floating point waveforms with much higher resolution
than can be stored in a 16-bit waveform file. This extra resolution
is not preserved when traces are recalled using flashback.



Cumulative Measurements

- Any measurements on when the

Lab Notebook entry is created are not saved individually in the
database (other than being embedded in the hardcopy image).
This means that when flashback is used, the measurements are
recomputed using the recalled waveform data. Normally, doesn't
pose a problem; however, if cumulative measurements were on
when the entry was stored and the cumulative measurements
accumulated data from multiple acquired waveforms, they lose
their history and show instead only the results from the stored
waveforms.

«
...
174
175
176
177
178
...
»

Содержание LabMaster 10 Zi Series












































































































































































































































Отзывы:

Нет отзывов