Teledyne LabMaster 10 Zi Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 235

Teledyne LabMaster 10 Zi Series Скачать руководство пользователя страница 38

Getting Started Guide

LM10Zi-GSM-E Rev A

31

Power Cable and Main Power Switch

Teledyne LeCroy advises that you note the power ratings of the
individual modules and connect them to suitably rated circuits.



MCM-Zi Control Module comes with an IEC60320 Type C13
power inlet connector.



LM10xx-Zi Acquisition Module comes with an IEC60320 Type C20
power inlet connector.

CAUTION

: The combined draw from your Master Control

Module and Acquisition Modules (max of 20) can be many kilowatts.
Two acquisition modules connected to a single circuit may cause an
overcurrent condition for that circuit.

When all connections are made, the main power switch on the front of
the

Master Control Module

powers on all components as a single unit.

NOTE

: If any connections are incorrect, the main power switch will not

power on the system.

Always refer to the product datasheet at www.teledynelecroy.com for
the most current and detailed specifications.

«
...
36
37
38
39
40
...
»

Содержание LabMaster 10 Zi Series












































































































































































































































Отзывы:

Нет отзывов