Teledyne LabMaster 10 Zi Series Скачать руководство пользователя страница 154

Страница: 154 / 235

Getting Started Guide

LM10Zi-GSM-E Rev A

147

ERSISTENCE

IGMA

Using this math operator, you can enter a scale, measured in standard
deviations, by which to create a new waveform.

Viewing Trends

This procedure explains how to view the Trend of a math function or
measurement parameter applied to a waveform. A Trend shows... See

Track vs. Trend

(on page 142) for a better understanding of the

information a Trend provides.

In the menu bar, touch

Measure → Measure Setup...

Touch one of parameter tabs

showing its corresponding

dialog.

Now, on the dialog, touch inside the

Source1

data entry field and

select an input waveform from the pop-up menu.

Touch inside the

Measure

data entry field and select a parameter

from the pop-up menu.

Touch the

Trend

button at the bottom of the dialog.

Now, from the

Math selection for Trend

menu, select a math

function location

in which to store the

Trend

display. The

Trend is then shown along with its respective trace descriptor
label for the selected math function.

Touch the newly displayed Trend math function trace label to
change settings on the Trend dialog (located on the Trend tab at

Содержание LabMaster 10 Zi Series












































































































































































































































Результаты поиска

Содержание LabMaster 10 Zi Series

Отзывы:

Teledyne LabMaster 10 Zi Series, Руководство оператора, Страница: 154 / 235

Результаты поиска

Содержание LabMaster 10 Zi Series

Отзывы: