Teledyne LabMaster 10 Zi Series Скачать руководство пользователя страница 162

Страница: 162 / 235

Getting Started Guide

LM10Zi-GSM-E Rev A

155

Actions Dialog

Various configurations can be made to all or some of your Pass/Fail
conditions using the

Actions

dialog.

By touching the

Stop Test

checkbox in the

Actions

dialog, you can set up

the test to end after a predetermined number of sweeps that you
decide.

You can also decide the actions to occur upon your waveforms' passing
or failing, by selecting one or all of the following:



Stop



Audible alarm



Print image of display



Emit pulse (if available)



Save waveform

The Pulse checkbox causes a pulse to be output through
the Aux Out connector at the front of the oscilloscope.

This pulse can be used to trigger another oscilloscope.

You can set the amplitude and width of the pulse as described in
Auxiliary Output Signals.

Depending on your oscilloscope model, you can configure up to 8
pass/fail conditions. The Boolean conditions to determine if your
waveform passes are as follows:

Содержание LabMaster 10 Zi Series












































































































































































































































Результаты поиска

Содержание LabMaster 10 Zi Series

Отзывы:

Teledyne LabMaster 10 Zi Series, Руководство оператора, Страница: 162 / 235

Результаты поиска

Содержание LabMaster 10 Zi Series

Отзывы: