Teledyne LabMaster 10 Zi Series Скачать руководство пользователя страница 122

Страница: 122 / 235

Getting Started Guide

LM10Zi-GSM-E Rev A

115

Display Setup

Access and adjust the different display configurations on the
oscilloscope using the following steps:

NOTE

: Not all grid styles are available on all instruments. Grid styles vary

based on both oscilloscope model and whether or not you have the SDA
III software option loaded on your oscilloscope.

From the menu bar, touch

Display → Display Setup...

Touch one of the

display types



Auto Grid

automatically adds or deletes grids as you select more

or fewer waveforms to display.



If many display setups are available for your oscilloscope, choose
the

Grid

option to display the

Select Grid

pop-up.

Touch inside the

Grid Intensity

data entry control and provide a

value from 0 to 100.

Touch the

Grid on top

checkbox if you want to superimpose the

grid over the waveform.

NOTE

: Depending on the grid intensity, some of your waveforms

may be hidden from view when the grid is placed on top. To
undo, simply uncheck

Grid on top

Содержание LabMaster 10 Zi Series












































































































































































































































Результаты поиска

Содержание LabMaster 10 Zi Series

Отзывы:

Teledyne LabMaster 10 Zi Series, Руководство оператора, Страница: 122 / 235

Результаты поиска

Содержание LabMaster 10 Zi Series

Отзывы: