Teledyne Analytical Instruments LXT-380 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 104

background image

LXT-380 Universal Transmitter

SP3X Sensors

Teledyne Analytical Instruments

61

removing hard water scales and metallic deposits or spray washing for
flocculants and biofilms.

8.3.1 ELECTRODE CARTRIDGE INSTALLATION

Unless ordered separately, electrode cartridges are generally

shipped installed in a sensor. Sensors ordered without an electrode are
shipped with a shipping plug to keep contamination from getting inside
the sensor during shipment or storage. The following procedure explains
how to install the electrode cartridge in the sensor assembly:

1.

Remove the shipping plug by turning it counterclockwise.

2.

Remove the electrode cartridge from the protective soaker
boot.

Be careful not to flex the electrode body while removing

the tape and the protective boot.

3.

Rinse the electrode tip in tap water and wipe the electrode
body dry then lubricate the o-ring seals with the included
lubricant.

Save the protective soaker boot in the event the

electrode must be stored at a future time

.

4.

Carefully insert the electrode cartridge into the sensor
assembly by turning until

hand tight

. The first o-ring, closest

to the front of the electrode, will be slightly visible if held
horizontally.

Note: If excess force is required during electrode installation,

check for proper thread engagement or for an obstruction.

8.3.2 ELECTRODE CARTRIDGE REPLACEMENT

Periodic replacement of the electrode cartridge is required for pH,

ORP and Specific Ion sensors. The following procedure explains how to
replace the electrode cartridge in the sensor assembly:

1.

Remove the electrode cartridge from the front of the sensor
assembly by turning it counterclockwise.

2.

For installation procedure follow steps 2, 3, and 4 in section
8.3.1 electrode cartridge installation.

«
...
78
79
80
81
82
...
»

Содержание LXT-380









































































































Отзывы:

Нет отзывов

Похожие инструкции для LXT-380

Бренд: Nautel Страницы: 4

Бренд: Yaesu Страницы: 84

Бренд: Yaesu Страницы: 2

Бренд: Yaesu Страницы: 42

Бренд: Yaesu Страницы: 46

Бренд: Yaesu Страницы: 2

Бренд: Yaesu Страницы: 20

Бренд: Yaesu Страницы: 96

Бренд: Yaesu Страницы: 55

Бренд: Yaesu Страницы: 2

Бренд: Yaesu Страницы: 78

FT DX 9000 CONTEST - 2

Бренд: Yaesu Страницы: 410

Бренд: Yaesu Страницы: 132

FT-100 Micro Mobile

Бренд: Yaesu Страницы: 55

FT-2000 - MENU MODE LIST

Бренд: Yaesu Страницы: 206

Бренд: Yaesu Страницы: 17

FT-2000 - MENU MODE LIST

Бренд: Yaesu Страницы: 18

Бренд: Yaesu Страницы: 131

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды