Teledyne Analytical Instruments LXT-380 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 104

background image

LXT-380 Universal Transmitter

SP3X Sensors

Teledyne Analytical Instruments

55

8.0 SP3X SENSORS

SP3X sensors are a family of digital sensors designed for use with

the Model LXT-380 transmitters. SP3X sensors accept the standard
Teledyne electrode cartridges. The SP3X sensors convert the analog
signals into a temperature compensated digital protocol that allows two
way communications with the transmitter. The type of sensor, identity
and serial number are stored in the sensor’s memory along with three
calibration registers. When connected to a Teledyne digital analyzer the
sensor’s information is uploaded to the analyzer configuring the displays
and outputs to the values appropriate to the sensor’s measured
parameter. Connect an SP3X pH sensor to a Model LXT-380
Transmitter and the Transmitter configures itself into a calibrated pH
transmitter.

The internal components of the SP3X sensors, the signal

conditioner, temperature sensor and cable assembly are epoxy
encapsulated inside the ¾” O.D. housing. Epoxy encapsulation of the
components increases the reliability of the sensor by eliminating failures
caused by wiring and connector breakage. The SP3X sensors use the
same easily replaceable electrode cartridges as the S10 and S17 sensor
assemblies.

8.1 SP3X INSTALLATION

Four typical installation configurations are available for Teledyne

sensors: insertion, immersion, flow-through and valve-retraction.
Although there are many ways to accomplish these mounting
configurations, Teledyne recommends the following installation
configurations.

8.1.1 INSERTION

The SP3X sensor is installed using a ¾” MNPT compression fitting

with choice of nylon, Teflon or 316 SS ferrule. The ¾” MNPT can be
inserted into a pipe Tee or through a tank wall, the SP3X is then inserted
through the fitting and compression gland is tightened to secure the

«
...
72
73
74
75
76
...
»

Содержание LXT-380









































































































Отзывы:

Нет отзывов

Похожие инструкции для LXT-380

Pacemark PM4410

Бренд: Oki Страницы: 2

Бренд: Icom Страницы: 47

Realvision RV-220P

Бренд: Raymarine Страницы: 24

Бренд: Evikon Страницы: 4

Бренд: DigiSender TV Страницы: 20

Бренд: Zaxcom Страницы: 37

Бренд: Adeunis RF Страницы: 9

Бренд: Hallicrafters Страницы: 30

Бренд: Me Страницы: 50

Бренд: Sennheiser Страницы: 34

Бренд: GRASS VALLEY Страницы: 53

Бренд: Ningbo Страницы: 11

wirelessHART Rosemount Series

Бренд: Emerson Страницы: 56

Бренд: Emerson Страницы: 18

Rosemount 8712C

Бренд: Emerson Страницы: 4

Rosemount X-well 648

Бренд: Emerson Страницы: 90

Rosemount Analytical HART 5081-A-HT

Бренд: Emerson Страницы: 112

Rosemount 644 FOUNDATION

Бренд: Emerson Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды