TECO T-verter N2 Series Скачать руководство пользователя страница 56

Страница: 56 / 83

Fn_78: Over Torque Detection Level:

30 - 200 %

Fn_79: Over Torque Detection Time:

0 - 25 sec

Note:

1. Definition of the over torque feature: the output current (rated current is 100%) remains above

over torque detection level (Fn_78) during over torque detection time (Fn_79).

2. (Fn_77) is set to (x0xx) When over torque occurs, the T-verter continues running and display

the blinking “OL3” light until the output current is lower than the (Fn_78) setting.

(Fn_77) is set to (x1xx) When over torque occurs, the T-verters base blocks immediately and

the display blinks “OL3”. To re-start the drive, it is necessary to press RESET key.

3. When (Fn_61) (Fn_62) or (Fn63) (multi-function output terminal control) is set to 05, the

multi-function output provides an over torque detection signal. The over torque detection

output signal is available only if (Fn_77) is set to (xxx1)

Fn_80:

S-Curve Set-up:

Time (1) Acceleration & Deceleration:

0 to 4 Sec.

Fn_81:

S-Curve Set-up:

Time (1) or (2) Acceleration & Deceleration: 0 to 4 Sec.

Formula for Calculating Acceleration and Deceleration Time.

Accel. Time = (Fn_01) or (Fn_49) X

Decel. Time = (Fn_02) or (Fn_50) X

100% of Speed

100%
Torque
&
Horse
Power

Current Detection

S-Curve

Ramp Profile

Time at Speed

Preset Frequency

60 Hz

Preset Frequency

60 Hz

Содержание T-verter N2 Series




















































































Результаты поиска

Содержание T-verter N2 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO T-verter N2 Series, Руководство по эксплуатации

Результаты поиска

Содержание T-verter N2 Series

Отзывы:

Бренды по названию

Популярные бренды