manualshive.com logo in svg

TECO T-verter N2 Series, Руководство по эксплуатации

Поделиться
Скачать
TECO T-verter N2 Series Скачать руководство пользователя страница 51

 

48

 

12 /13 UP / DOWN command 

    

RUN 

 

UP 

 

DOWN 

 

 

Output                       

frequency      Fn_25 

 

 

Note: 

To utilize the up and down function (Fn_11) must be set to terminal control.  

When using this function set (Fn_03) to the (0xxx) position. The T-verter will accelerate to the 

target frequency set at (Fn_25) after the designated terminal is turned on, the drive will remain at 

what ever speed it was at when the contact terminal was released.   

 

When the (UP) or (DOWN) terminal is engaged, the T-verter starts accelerating or decelerating.  

When the UP or DOWN signal disappears, the T-verter will stay at the current frequency.  Once 

the operating signal is off, the T-verter will decelerate to a stop or stop immediately (decided by 

Fn_44), the operation frequency will be recorded in (Fn_25)   

Terminal UP or DOWN control is inactive during the stop mode.  The target frequency must be 

changed at (Fn_25) through the Keypad. 

    

Fn_61: 

Multi-Function Output:  Terminals 10 / 11  

00: Run Mode 

01:  At Target Speed 

02:  Set Frequency (Fn_08) +/- (Fn_09) 

03:  Frequency Detection > (Fn_08) 

04:  Frequency Detection < (Fn_08)  

05:  Over Current Detection 

06:  Change contact status From (NO) to (NC) 

 

Содержание T-verter N2 Series




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды