TECO T-verter N2 Series Скачать руководство пользователя страница 46

Страница: 46 / 83

Fn_44:

Stopping Mode and Braking Resistor Protection

xxx0

: Decel. to stop

xxx1

: Free fun to stop

xx0x

: Braking resistor overheat protection disable

xx1x

: Braking resistor overheat protection enable

Note:

If the (Fn_44) is set at free run to stop, the T-verter will cut off the output after receiving a stop

instruction and the motor will coast to a stop.

If the (Fn_44) is set for deceleration to stop, the T-verter will decelerate to the frequency set by

(Fn_54) after receiving deceleration instructions, the output voltage level set at (Fn_55) the

T-verter will stop after the time period set by (Fn_53)

If the (Fn_44) is set for protection of the Built-in braking transistor, and operation of drive is too

frequently decelerate, the braking transistor and braking resistor may overheat and T-verter will

trip. OH1 will show this on Keypad display. The T-verter can be manually restarted after the

braking resistor has cooled off. If the braking resistor is damaged and leads to OV-C trip,

deceleration time must be increased or the external braking resistor replaced.

Fn_45: Adjustment for Analog out put for Meters

Fn_46: Multi-function Analog output Meter Selection

0 - 3

0: Output freq.(Fn_06 max) : 10Vdc / (Fn_06)

1: Set frequency (Fn_06 max): 10Vdc / (Fn_06)

2: Output voltage (Vac)

: 10Vdc / (Fn_30)

3: DC voltage

:(10Vdc / 450 Vdc: for 200V series)

(10Vdc / 900 Vdc: for 400V series)

Fn_47: Meter Display Mode

xxx0 :

Output Voltage display

disable

xxx1 :

Output Voltage Display

enable

xx0x :

DC Voltage Display

disable

xx1x : DC Voltage Display

enable

x0xx :

Output Current

disable

x1xx

Output

Current enable

(Meters)

Содержание T-verter N2 Series




















































































Результаты поиска

Содержание T-verter N2 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO T-verter N2 Series, Руководство по эксплуатации

Результаты поиска

Содержание T-verter N2 Series

Отзывы:

Бренды по названию

Популярные бренды