TECO T-verter N2 Series Скачать руководство пользователя страница 50

Страница: 50 / 83

09 Control signal selection

Multi-input terminal OFF: Operation command/ Freq command is from digital operator or remote

control (TM2), according to the setting of Fn_10 / Fn_11

Multi-input terminal ON: Operation command/ Freq command is from digital operator regardless

of the setting of Fn_10 / Fn_11

10 Communication control mode selection

Multi-input terminal OFF: During communication, Inverter can receive Rnu/Freq signals from

control unit (PC or PLC), Parameter can be changed by control unit, Run/Freq signals from

Keypad and TM2 will be ineffective, Keypad can be used for displaying Voltage / Current /

Frequency or emergency stop but can not be used for changed parameters

Multi-input terminal ON: During communication, The Rnu/Freq command is controlled by

Inverter itself, Control unit (PC or PLC) is just for reading parameters.

11 Accel/Decel Prohibit

The T-verter will stop accelerating or decelerating when Accel. / Decel. Prohibit signal is

activated. When the signal is removed, the T-verter continues accelerating or decelerating.

Run

Command

Accel./Decel. (*)

Prohibit

Output

*: When the “Run” command is off, the Accel and Decel prohibit command is inactive.

Содержание T-verter N2 Series




















































































Результаты поиска

Содержание T-verter N2 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO T-verter N2 Series, Руководство по эксплуатации

Результаты поиска

Содержание T-verter N2 Series

Отзывы:

Бренды по названию

Популярные бренды