TECO T-verter N2 Series Скачать руководство пользователя страница 49

Страница: 49 / 83

00 : SP1 (Multi-speed 1)

Please refer to (Fn_17)

01 : SP2 (Multi-speed 2)

Please refer to (Fn_17)

02 : SP3 (Multi-speed 3)

Please refer to (Fn_17)

03 : Jog operation

Please refer to (Fn_17)

04 : Accel. / Decel. Time selection

Please refer to (Fn_01)

05 : External Emergency Stop

06 : External Base Block Command

07 : Speed search :

Please refer to (Fn_48)

08 : Energy saving mode :

Please refer to (Fn _82)

09 : Control Signal Selection

10 : Communication Control Mode Selection

11 : Accel. / Decel. Prohibit

12 : UP command

13 : DOWN command

14 : Sequence control

Please refer to (Fn_17) (Fn_84) ~

(Fn_91)

15 : Master / Auxiliary speed selection :

Please refer to (Fn_11)

16 : (N/O - normal open contact) to (N/C - normal close contact)

Note:

(Fn_56) will be ineffective when Terminal 6 is used for 3-wire control There are 32 combinations

that can be selected as above by terminals 6, 7, 8, (Fn_56) (Fn_57) (Fn_58)

05 External Emergency Stop

As soon as external emergency stop signal is received, the T-verter will Decel. to a stop

(regardless of the setting in (Fn_44) the display will blink "E.S." After this signal is removed,

either turns OFF and ON the RUN command again to reset. The in verter will restart from the start

freq. If the Emergency stop signal is removed before the T-verter stops, T-verter will still execute

the emergency stop.

06 External Base Block Command

The Base Block Command can be found in the Multifunction input assignment group (6), As soon

as Base Block signal is applied, the T-verter output is shut off regardless of the setting in (Fn_44)

and the display will blink "b.b.". After the base block input is removed, either turn OFF and ON

again run command, or to press the RUN key and the T-verter will restart from the start freq.

The Fault contact is controlled by Fn_97:

When Fn_97=0xxx Fault contact is not energized after external base block

When Fn_97=1xxx Fault contact is energized after external base block

Содержание T-verter N2 Series




















































































Результаты поиска

Содержание T-verter N2 Series

Отзывы:

Бренды по названию

Популярные бренды

TECO T-verter N2 Series, Руководство по эксплуатации

Результаты поиска

Содержание T-verter N2 Series

Отзывы:

Бренды по названию

Популярные бренды