TCS Basys Controls SZ1022N, Руководство по эксплуатации продукта

Страница: 13 / 20

R
2800 LAURA LANE • MIDDLETON, WI 53562 • (800) 288-9383 • FAX (608) 836-9044 • www.tcsbasys.com
13
Pointmap Table for SZ1022N (See page 16 for Pointmap Table for SZ1024N)
NPT NPA UNITS POINT DESCRIPTION RANGE/VALUE ADDITIONAL NOTES
ADI 1 # DI2 control mode 0=cool lockout See Setup (page 8).
1=monitor
2=service
ADI 2 # DI3 control mode 0=filter service See Setup (page 7).
1=external override
2=external time clock
ADI 3 # Occupied Fan mode 0=on, 1=cool, 2=auto Fan Switch button on keypad.
ADI 4 # System mode 0=off,1=auto,2=heat System Switch button on keypad.
3=cool
ADI 5 Day Internal time clock day 0-6, mon to sunday Day of Week.
ADI 6 Hours Internal time clock hours 0-23 0-11 (AM), 12-23 (PM).
ADI 7 DegF (C) Setpoint adjust limit from keypad 0-50 (0-28) Limits keypad adjustment of occupied
heating and cooling setpoints. See note 5.
ADI 8 DegF Differential for cool stage 1 0-50
ADI 9 DegF Offset for cool stage 1 0-50
ADI 10 DegF Differential for cool stage 2 0-50
ADI 11 DegF Offset for cool stage 2 0-50
ADI 12 DegF Differential for heat stage 1 0-50
ADI 13 DegF Offset for heat stage 1 0-50
ADI 14 DegF Differential for heat stage 2 0-50
ADI 15 DegF Offset for heat stage 2 0-50
ADI 16 DegF Differential for stage 3 0-50 Stage 3 can do either Heating or Cooling.
ADI 17 DegF Offset for stage 3 0-50
ADI 18 DegF Setpoint shift value 0-50 When DI2 is selected Monitor, this is
number of degrees that the occupied
cooling setpoint is shifted up and the
heating setpoint is shifted down.
ADI 19 Seconds Internal time clock second 0-59
ADI 20 Minutes Internal time clock minute 0-59
ADI 21 DegF (C) Occupied heating setpoint 40-90 (4-32) Occupied heating setpoint must be less
than occupied cooling setpoint.
ADI 22 DegF (C) Unoccupied heating setpoint 40-90 (4-32) Unoccupied heating setpoint must be
less than unoccupied cooling setpoint.
ADI 23 DegF (C) Occupied cooling setpoint 40-90 (4-32)
ADI 24 DegF (C) Unoccupied cooling setpoint 40-90 (4-32)
ADI 25 DegF (C) Room temperature 40-90 (4-32) Read only. See Note 5.
ADI 26 DegF (C) Discharge air low limit 0-150 (-18-65) Discharge air high limit must be greater
than discharge air low limit.
ADI 27 DegF (C) Discharge air high limit 0-150 (-18-65)
ADI 28 DegF (C) Discharge air temperature 0-150 (-18-65) Read only.
ADI 29 Minutes Override period 0-255 Unoccupied override time allowed.
ADI 30 Seconds Power on delay time 0-255 Time before control begins on powerup.
ADI 31 Minutes Remaining override time 0-255 Read Only. Time remaining before the
override period expires.
ADI 32 DegF (C) Current user setpoint adjust -50-50, (28-28) Read Only. + or - amount the occupied
setpoint has been adjusted from actual
settings. (See Note 5.)
ADI 33 Minutes Monday Occupied start time 0-1440 There are two occupied and two un-
for schedule A occupied time periods allowed per day.
ADI 34 Minutes Monday Occupied end time 0-1440
for schedule A All times are measured in minutes from
ADI 35 Minutes Monday Occupied start time 0-1440 midnight.
for schedule B
ADI 36 Minutes Monday Occupied end time 0-1440
for schedule B
ADI 37 Tuesday 0-1440
ADI 38 Tuesday 0-1440
ADI 39 Tuesday 0-1440