background image

R

2800 LAURA LANE •  MIDDLETON, WI 53562 •  (800) 288-9383 •  FAX (608) 836-9044 •  www.tcsbasys.com

11

LED Description                 

Six LEDs on the face allow the occupant to view the current
operating status of the thermostat. 

OCCUPIED

This LED will be lit whenever the unit is operating in the
occupied mode.

HEATING

This LED will be lit when any heat output is closed.

COOLING

This LED will be lit when any cooling output is closed. 

FAN

This LED will be lit when the fan output is closed.

SERVICE

This LED will be lit when the high or low discharge air limit
has been reached, when the fan interlock has indicated
failure,  or when the filter service or service input are closed. 

PROGRAM/DATA

This LED will be lit when the thermostat is within the
programming or clock setup menus. It will blink when the
unit is being accessed by a PC.
Additional monitoring is available by continually pressing the
service key. 

MON  

72F

12:00 AM

DISCHARGE AIR

55F

SERVICE STATUS

OK

TEMP

1.

2.

3.

service

status

service

status

service

status

service

status

fan

Occup ied

H eatin g

C oolin g

Fa n

Service

Pro gram/

COOLER

WARMER

D ata

switch

service

status

system

switch

program

setup

clock
setup

override

OVERRIDE

178 MINUTES

Conventional H/C

continue

Heat Pump

Go to 4b.

ON

Main Monitoring Screen.

Press the service

button to access the following screens. 

Service Screen.

This message may be

followed by any or all of the following:
CHECK FILTER, CHECK FAN, DISCHARGE
HIGH, DISCHARGE LOW, or CHECK DI2.

Discharge Air Temperature Screen.

Shows

discharge air temperature if sensor is used. 

Override Status Screen.

Shows whether 

the override is active and if so, how many
minutes remaining.

HEAT STAGE 1 OFF

COOL STAGE 1    ON

COOL STAGE 3    OFF

4a.

5a.

6a.

HEAT STAGE 2 OFF

COOL STAGE 2    OFF

FAN STATUS       OK

service

status

service

status

7.

DI2 SERVICE      OFF

FILTER                OK

MON 

72F

12:00 AM

service

status

service

status

service

status

COM P STAGE 1   ON

AUX HEAT 1       ON

REV VALVE     OPEN

4b.

5b.

6b.

COM P STAGE 2    OFF

AUX HEAT 2      OFF

FAN STATUS       OK

service

status

service

status

Heat Stages Status Screen. 

Shows

the status of the first and second
stages of heating. 

Cool Stages Status Screen. 

Shows

the status of the first and second
stages of cooling. 

Third Stage and DI1 Status Screen.

Shows the status of the third stage
and the status of the fan interlock if
DI1 is set for fan interlock. 

Compressor Stages Status Screen.

Shows the status of the first and
second stage compressors.  

Auxiliary Heat Stages Status
Screen. 

Shows the status of the first

and second stages auxiliary heat. 

Reversing Valve and DI1 Status
Screen.

Shows the position of the

reversing valve as either heat or cool
and the status of the fan interlock or
DI1. 

DI2 and DI3 Status Screen.

Shows

the cool lockout into DI2 or DI2 status
and filter status or DI3 status. 

Main Monitoring Screen.

Содержание SZ1022N





















Отзывы: