Installing the Equipment
Reference Guide: evolution 5000 E5780 and E5782 Encoder
Page 2-13
ST.RE.E10135.4
Table 2.7: Audio In Connector
Pin
Signal
Pin
Signal
Analogue
Digital
Analogue
Digital
1
Left Channel A (+)
AES/EBU (A) (+)
9
Left Channel A (-)
AES/EBU (A) (-)
2
Not connected
10
Right Channel A (+)
3
Right Channel A (-)
11
Not connected
4
Left Channel B (+)
AES/EBU (B) (+)
12
Left Channel B (-)
AES/EBU (B) (-)
5
Not connected
13
Right Channel B (+)
6
Right Channel B (-)
14
Not connected
7
AES/EBU
Reference (Signal)
15
AES/EBU
Reference (Ground)
8 Not
connected
NOTES…
1.
In analogue mode termination is either 20 k
Ω
or 600
Ω
.
2.
In AES/EBU mode termination is 110
Ω
.
3.
When the Encoder is powered down the digital channel is selected with 110
Ω
termination.
4.
The digital audio input does not support SPDIF.
5.
In order to comply with EMC regulations, use the audio break-out cable supplied with the unit.
2.6.7
ASI OUT 1, 2 and 3 Outputs
Connect the Multiplexer or Modulator ASI cable to the appropriate
ASI OUT connector, using good quality 75
Ω
coaxial cable (for
example, BBC PSF 1/3).
A 75
Ω
BNC connector provides the output from the Encoder.
Table 2.8: ASI OUT 1, 2 and 3 Connectors
Pin Signal
Centre Signal
Screen Ground
2.6.8 Control
Interfaces
Connection
Operation of the Encoder from a TANDBERG Television control system is via the Ethernet
network running the Simple Network Management Protocol (SNMP) protocol. Connect the
ETHERNET
connector to the controller (for example, MEM). Local control is implemented
through the front panel keypad and display. See
Chapter 4, Operating the Equipment Locally
for details of how to access the front panel menus.
Ethernet #1 and #2
An 8-way, RJ-45 connector provides a 10BaseT Ethernet interface
for communications with the MEM for control and monitoring. The
Encoder has a single switched Ethernet channel. Ethernet#1 is
selected as default at power-up. If a carrier is not detected on
Ethernet#1 then the input switches to Ethernet#2. This gives a
redundant Ethernet control via two hubs.
Содержание E5780
