Installing the Equipment
Reference Guide: evolution 5000 E5780 and E5782 Encoder
Page 2-5
ST.RE.E10135.4
2.3.2 Cable
Routing
Power supply cables should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them. Pay particular attention to cables at plugs, convenience
receptacles, and the point where they exit from the appliance.
Do not run a.c. power cables in the same duct as signal leads.
2.3.3 Equipment
Access
WARNING...
BERYLLIUM COPPER FINGER STRIPS ARE USED IN THIS EQUIPMENT TO SEAL THE
ENCLOSURE FOR EMI PROTECTION. THIS ARRANGEMENT IS PERFECTLY SAFE DURING
NORMAL OPERATION. DO NOT FILE THE STRIPS OR OTHERWISE CAUSE THEM TO PRODUCE
DUST OR PARTICLES. ANY CUTS CAUSED BY THE STRIP SHOULD BE TREATED
APPROPRIATELY.
Ensure that the Encoder is installed in such a way as to allow access to the rear of the unit
and the connectors.
2.3.4 Ventilation
WARNING...
NEVER PUSH OBJECTS OF ANY KIND INTO THIS EQUIPMENT THROUGH OPENINGS AS THEY
MAY TOUCH DANGEROUS VOLTAGE POINTS OR SHORT-OUT PARTS THAT COULD RESULT IN
A FIRE OR ELECTRIC SHOCK. NEVER SPILL LIQUID OF ANY KIND ON THE PRODUCT.
CAUTIONS...
1. Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product
and to protect it from overheating, and these openings must not be blocked or covered. This product
should never be placed near or over a radiator or heat register. This product should not be placed in
a built-in installation such as a rack unless proper ventilation is provided or the instructions have
been adhered to.
2. Do not install equipment so that the air intake of one aligns with the outlet on another. Provide
baffles and adequate spacing.
3. The fans contained within this unit are not fitted with a dust/insect filter. Pay particular attention to the
environment in which it is to be used.
The unit is designed for stationary or fixed use only. Ensure it is firmly and safely located and
has an adequate through-flow of air. Allow at least 50 mm free air-space at each side of the
equipment. Units in racks can be stacked without ventilation panels between. Racks
containing stacked equipment may need to be forced-air cooled to reduce the operating
ambient temperature. For stacking constraints contact Customer Services.
It is important not to block the front air intake on the bottom-left corner of the front panel (see
Содержание E5780
