manualshive.com logo in svg

Symmetricom TimeProvider 500 series, Справочное руководство

Поделиться
Скачать
Symmetricom TimeProvider 500 series Скачать руководство пользователя страница 86

TMSL 097-44018-26

Issue 2: Sep 99

Page 86

COMMAND CODE: RTRV-COM (Contd)

RESPONSE FORMAT (Cont)

parameter

value

meaning

comtype

X25

this port is set for PAD

MODEM

this port is set for modem

TERM1

dumb terminal (VT100 with no DSR/DTR support and message buffering dis-
abled)

TERM2

dumb terminal (VT100 with DSR/DTR support and message buffering enabled)

REMOTE

allows communication with a remote shelf via the specified communication port

endoftext

0–9F

this hexadecimal number sets an additional character as the end-of-text mes-
sage. 0 indicates no end-of-text message. This character does not replace the
TL1 end-of-text terminator (;)

echo

ALW

local echo is allowed on this port

INH

local echo is inhibited on this port

compri

INH

communication through a port with this designation is inhibited (INH is not al-
lowed on COM2)

ALW0

allows normal communication; autonomous messages are not sent out a port
with this priority level

ALW1

allows normal communication; autonomous messages are always sent out this
port regardless of the priorities of the other ports (this is the highest port priority)

ALW2

allows normal communication; autonomous messages are sent out this port only
if there are no ports with a priority level of ALW1 (this is the second-highest port
priority)

ALW3

allows normal communication; autonomous messages are sent out this port only
if there are no ports with a priority level of ALW1 or ALW2 (this is the lowest port
priority)

hwcontrol

ALW

external equipment is allowed to stop the DCD system from sending messages
by setting the clear to send (CTS) lead low, or continue messages by setting the
CTS lead high

INH

external equipment is inhibited from controlling DCD system messages by ma-
nipulation of the clear to send (CTS) lead

swcontrol

ALW

user is allowed to use a Control-s key combination to stop the DCD system from
sending messages; also allows the user to use a Control-q key combination to
cause the DCD system to continue sending messages

INH

the use of the Control-s and Control-q key sequences to stop and start messag-
es is inhibited

dur

1–45

time in minutes after which a user is logged off if there is no activity

dn

0–32
numeric
characters

the remote PAD address

Содержание TimeProvider 500 series






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды