manualshive.com logo in svg

Symmetricom TimeProvider 500 series, Справочное руководство

Поделиться
Скачать
Symmetricom TimeProvider 500 series Скачать руководство пользователя страница 67

Issue 2: Sep 99

TMSL 097-44018-26

Page 67

COMMAND CODE: OPR-PROTNSW (Contd)

PURPOSE (Contd)

1-for-N protection:

This command is only for timing output cards other than the TO-EA5, EA10, EA10M, EA20, & EA20M
that are set for 1:N protection. The OPR-PROTNSW and RLS-PROTNSW commands switch between a
timing output card and a protection timing output card of the same type in an HS slot.

•

The OPR-PROTNSW command is used to switch from a timing output card in a TO slot to a
protection card of the same type in an HS slot.

•

The RLS-PROTNSW command is used to switch back to a timing output card in a TO slot from
a protection card in an HS slot.

INPUT 

OPR-PROTNSW:[<tid>]:<aid>:<ctag>::<switchfrom>;

The parameter values in the table below are as follows:

a

= 1–10 for MCA, 1–12 for MAN

Note:  

If automatic switching was set with the SET-ATTR-CONT command and revertive switching

was not set with the SET-ATTR-CONT command and a fault occurred in the working card, then the
working card with the fault was replaced, the two commands (OPR-PROTNSW and RLS-PROTNSW)
reverse function. That is, the OPR-PROTNSW must be used to return to the working card, and the
RLS-PROTNSW must be used to transfer to the protection card.

parameter

value

meaning

aid

TO-a

timing output card

switchfrom

MAN

this value, used with 1-1 protection, causes a protection switch from the 
working timing output card in slot TO-a to the mate protection timing out-
put card in the adjacent slot (used with TO-EA5, EA10, EA10M, EA20, 
& EA20M cards only)

MCA

this value, used with 1:N protection, causes a switch from the working 
timing output card in slot TO-a to the protection timing output card in the 
HS slot (used with cards other than TO-EA5, EA10, EA10M, EA20, & 
EA20M)

Содержание TimeProvider 500 series






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды