Symmetricom TimeProvider 500 series Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 165

background image

Issue 2: Sep 99

TMSL 097-44018-26

Page 69

COMMAND CODE: OPR-SWDX-PORT

PURPOSE

OPERATE SWITCH DUPLEX PORT

This command is for DCIM cards only. This command forces a particular reference input port on a par-
ticular DCIM card to be used. This command can be completed only if the <reference condition> for the
port has been set to ALW by the ED-PORT or ENT-PORT command.

Caution: If the port specified in this command fails, the clocks will go into holdover.

Stand-alone:

If the DCIM cards have been set for stand-alone operation (<conttype> = NO by the SET-

ATTR-CONT command), one of the following will occur:

If the specified port is on the active DCIM card: the active DCIM card, and therefore the system,
will use the signal on the specified input port.

If the specified port is on the inactive DCIM card: the inactive DCIM card, but not the system, will
use the signal on the specified input port.

1+1:

If the DCIM cards have been set for combined operation (<conttype> = 1+1 by the SET-ATTR-

CONT command), one of the following will occur:

If the specified port is on the active DCIM card: the active DCIM card, and therefore the system,
will use the signal on the specified input port.

If the specified port is on the inactive DCIM card: the inactive DCIM card will become the active
card, and the newly activated DCIM card, and therefore the system, will use the signal on the spec-
ified input port.

To determine the protection mode of the DCIM cards, use the RTRV-ATTR-CONT command (<conttype>
= NO or 1+1).

INPUT

OPR-SWDX-PORT:[<tid>]:<aid>:<ctag>;

The parameter values in the table below are as follows:

a

= 1–2

b

= 1–2

aid

meaning

DCIM-a-b

the specified port on the specified DCIM card

«
...
67
68
69
70
71
...
»

Содержание TimeProvider 500 series






































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TimeProvider 500 series

Бренд: T&D Страницы: 2

Бренд: X2E Страницы: 190

Бренд: Novus Страницы: 6

Бренд: Novus Страницы: 7

Бренд: RS PRO Страницы: 30

Бренд: JASTEC Страницы: 13

Бренд: National Instruments Страницы: 75

Бренд: AccuTherm Страницы: 12

Бренд: Omega Страницы: 32

Бренд: Eagle Tree Systems Страницы: 17

Бренд: Xylem Страницы: 2

Бренд: Sutron Страницы: 38

Бренд: Reed Instruments Страницы: 22

Бренд: Reed Instruments Страницы: 24

Бренд: Mikster Страницы: 2

Бренд: FlashTiming Страницы: 2

FortiSIEM 3500F

Бренд: Fortinet Страницы: 12

Бренд: Fortinet Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды