manualshive.com logo in svg

Symmetricom TimeProvider 500 series, Справочное руководство

Поделиться
Скачать
Symmetricom TimeProvider 500 series Скачать руководство пользователя страница 30

TMSL 097-44018-26

Issue 2: Sep 99

Page 30

COMMAND CODE: ED-COM (Contd)

INPUT FORMAT (Contd)

parameter

value

meaning

comtype

X25

for use with X.25 PAD (sets configuration for Black Box Corporation’s X.25 PAD-8 
only with the following settings:

a. drops call if idle time is greater than 1 minute
b. fixed destination id

Note: If the <comtype> is set to X25 and TimeScan NMS or TMN is used, refer to the 
PAD manual and the X.3 Standard to set the following parameters in the PAD Profile: 
disable ECHO, enable MESSAGES, and disable SERVICE SIGNALS.

MODEM

for use with modem with autodial (sets RS232 control leads to communicate with any 
Hayes-compatible modem that has autodial)

TERM1

for use with dumb terminal (VT100 with no DSR/DTR support and message buffering
disabled) (the autologoff feature will not function on a port with a comtype of TERM1)

TERM2

for use with dumb terminal (VT100 with DSR/DTR support and message buffering
enabled) or modem without autodial

REMOTE

allows communication with a remote shelf via the specified communication port

endoftext

00–9F

this hexadecimal number specifies 1 character as an additional end-of-text identifier; 
this character does not replace the TL1 end-of-text terminator (;); a 00 indicates that 
there is no end-of-text identifier (refer to an ASCII table for the hexadecimal code for 
a particular character)

echo

ALW

allows local echo

INH

inhibits local echo

compri

INH

communication through a port with this designation is inhibited (INH is not allowed on 
COM2)

ALW0

allows normal communication; autonomous messages are not sent out a port with 
this priority level

ALW1

allows normal communication; autonomous messages are always sent out this port 
regardless of the priorities of the other ports (this is the highest port priority)

ALW2

allows normal communication; autonomous messages are sent out this port only if 
there are no ports with a priority level of ALW1 (this is the second-highest port 
priority)

ALW3

allows normal communication; autonomous messages are sent out this port only if 
there are no ports with a priority level of ALW1 or ALW2 (this is the lowest port 
priority)

hwcontrol

ALW

allows external equipment to stop the DCD system from sending messages by 
setting the clear to send (CTS) lead low, or continue messages by setting the CTS 
lead high

INH

inhibits external equipment from controlling DCD system messages by manipulation 
of the clear to send (CTS) lead

Содержание TimeProvider 500 series






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды