manualshive.com logo in svg

SWF E-U1201, Руководство пользователя, Страница: 64 / 67

Поделиться
Скачать
SWF E-U1201 Скачать руководство пользователя страница 64

65

Embroidery
Contraction

Poor Trimmer
Operation

①

Strong tension of the upper

and lower thread

②

Too strong pressure of the

presser foot

③

Faulty needle
Abrasion and damage to the
tip of the needle or too big
needle for the thread used

④

Too big needle hole on the

needle plate for the needle
used

①

Fuse cut-off for trimmer

circuit

②

Bad trimmer motor

connection and poor motor
operation

③

Bad connector connection

④

Red light of the trimmer

drive box's indicator lamp

■

Adjust the tension of the

upper and lower thread

■

Replace the presser foot

pressure spring

■

Replace the needle

■

Use the needle of

appropriate standards

■

Check the 

fuse

condition on the joint board

■

Check the terminal for

trimmer motor connection
and replace the motor

■

Check the status of the

connector connection

■

After removing the cause of

trouble to the trimmer
system, press the reset key
to change the color of the
indicator light to be green

■

The hole on the

needle plate of SWF/

Series is 2.0mm.

The appropriate
thread and needle for
the SunStar needle
plate are as below:

■

Check the rated

voltage on the fuse
of the joint board

1) For 3-phase:

: 250V 10A

2) For 1-phase

: 250V 10A

Corrective Action and Check Point

Cause of Trouble

Type

Remarks

Cotton Thread: #50~#70
Rayon: #75~#120
Needle: DB

×

K5 #9~#14

Содержание E-U1201




































































Отзывы:

Нет отзывов