SWF E-U1201 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 67

SWF E-U1201 Скачать руководство пользователя страница 57

58

Wrong Needle
Bar Replacement

①

Wrong stop position

②

Failure to detect the signal

of rotating the needle position.
.

③

Wrong needle bar position

④

Wrong thread take-up lever
position

⑤

Inappropriate color change,
wrong muse for wiper
motor and wrong access to
connector

■

See the manual on the
wrong stop position

■

Execute manual color
change. Check whether the
signal lamp (N/Set LED
and LED of the concerned
needle) blinks at the same
time, and adjust the half-
turn film accordingly.

■

Adjust the location
properly.

■

Adjust the thread take-up
lever to be on the same line
with other thread take-up
levers when the machine
stops (main shaft rotary
angle 100°).

■

Replace the front fuse
within the control box or
check the connector part.

■

After manually
operating the main
shaft due to cleaning,
checking, and repair,
make sure to set the
main shaft's rotary
angle at 100°.

■

Adjustment of the
Thread Take-up Lever
Position Loosen the
screw for the driving
lever and adjust the
thread take-up lever
position in line with
other thread take-up
levers on the thread
take-up guide rail.

■

Check the rate
voltage of the fuse

= 250V 2A

Corrective Action and Check Point

Cause of Trouble

Type

Remarks

Screw for Thread Take-up
Driving Lever

Thread Take-

up Lever

«
...
55
56
57
58
59
...
»

Содержание E-U1201




































































Отзывы:

Нет отзывов