manualshive.com logo in svg

SWF E-U1201, Руководство пользователя, Страница: 56 / 67

Поделиться
Скачать
SWF E-U1201 Скачать руководство пользователя страница 56

57

CAUSES OF TROUBLE AND TROUBLESHOOTING

11

Wrong Machine
Operation and
Movement

Wrong Stop
Position

①

Excessive relaxation of the
belt tension or belt rupture

②

Power outage or circuit fuse
cut

③

Failure to detect the needle
position signal or detect the
signal once

④

Frame escape from the X, Y
movement limit.

⑤

Machine does not move
even after pressing the bar
switch.

①

Loose main shaft driving
belt

②

Wrong encoder position and
wrong encoder

■

Adjust the belt tension and
replace the belt

■

Check whether the main
shaft motor drive fuse is
cut, and replace the fuse 

■

Execute manual color
change. Locate the needle
at the highest position.
Check whether the signal
lamp (needle set and
concerned signal lamp
LED) blinks, and adjust the
half-turn film accordingly.

■

Return the frame to the
original position (within the
scope of the limit switch).

■

Check the operation status
of the limit sensor

■

Check the wiring of the
switch related to bar stitch
and the connector

■

Adjust the belt tension

■

Adjust the encoder position
or replace the encoder

■

Check the belt
depending on type of
trouble  

①

Main driving belt 

②

X-Y shaft timing
belt

Corrective Action and Check Point

Cause of Trouble

Type

Remarks

When a breakdown occurs, conduct repair or check in accordance with the
safety rules.

CAUTION

DANGER

Содержание E-U1201




































































Отзывы:

Нет отзывов