SWF E-U1201 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 67

SWF E-U1201 Скачать руководство пользователя страница 42

43

3) Adjustment of Moving Blade's Entering Angle

①

Loosen the two fixing screws for the blade
cam, and set the upper shaft rotary angle at
295° by using the hand pulley.

②

Turn the manual handle for trimmer
solenoid as in the figure to insert the roller
into the blade cam. Rotate the blade cam
until reaching the position where the roller
starts operating on the cam, and then tightly
fasten the two fixing screws.

③

After making adjustment of the entering
angle of the moving blade, make sure to
check whether the moving blade enters the
blade cam when the upper shaft rotary
angle is set at 295°.

10.1.2) Adjustment of Moving and Fixed Blades

Check the crossing tension of the moving and fixed
blades when the moving blade or the fixed blade is
replaced or repaired before making any adjustments.

①

Check the crossing tension
Manually move the moving blade to cut the upper
and lower threads, and check the conditions of the
cross-sections of the threads.

②

Adjust the crossing tension
Use the tension adjusting screw for the fixed
blade to adjust the crossing tension. When
adjusting the crossing tension, manually move the
moving blade, and check whether the fixed blade
crosses the moving blade in parallel from the
entry to the return to the original position.

Fixing Screw for Blade Cam

Manual Handle for
Trimmer Solenoid

Roller

Blade Cam

Moving Blade

Tension
Adjusting
Screw

Fixed Blade

1) If the crossing tension is too high, breakdown or abrasion might occur due to the

overload upon entry or returning. Make sure to properly adjust the crossing tension.

2) Conduct regular cleaning to remove the thread pieces around the lower thread holder

after using the embroidery machine for a time being. Otherwise, the thread pieces might
deteriorate the function of the lower thread holder.

CAUTION

«
...
40
41
42
43
44
...
»

Содержание E-U1201




































































Отзывы:

Нет отзывов