manualshive.com logo in svg

Suzuki Intruder VZR1800, Руководство по обслуживанию


Поделиться
Скачать
background image

 - 4/7 -

NOTE: The fuel delivery pipe assembly can be removed from the throttle body without

removing the throttle body assembly from the motorcycle.

1) Refer to section 6 of the service manual to remove the fuel tank and the air cleaner box.

Place shop rags over the bore of each throttle body to prevent anything from falling into

the engine through the throttle bodies.

2) Remove the wire harness clamp, disconnect

the fuel injector couplers 

A 

and move the

harness aside.

3) Remove the four fuel delivery pipe assembly

mounting screws and remove the fuel delivery

pipe assembly.

4) Replace the o-rings and seals with the new

parts supplied in the kit (apply a small amount

of engine oil to the o-rings and seals to ease

the installation of the injector).

To prevent damage to the o-rings or seals, don't turn the injector when pushing it into the fuel

delivery pipe and throttle body respectively.

Install the new fuel delivery pipe assembly in the reverse order of removal.

5) Connect the fuel injector couplers 

A 

and clamp the injector harness to the fuel delivery

pipe.

DO NOT overtighten the harness clamp.

6) Connect the fuel tank, remove the shop rags from over the bore of each throttle body,

and run the engine, checking for fuel leaks.

DO NOT reuse the original fuel hose connector retainer. Confirm that the fuel hose connector

has completely seated and locked (clicked) into position before turning on the ignition switch.

7) Refer to section 6 of the service manual to install the air cleaner box and the fuel tank.

8) Test ride the motorcycle to confirm proper operation.

FUEL DELIVERY PIPE ASSEMBLY REPLACEMENT PROCEDURE

When working with the fuel system, work in a well ventilated area away from any flame

or ignition sources. Store the motorcycle in an area away from any flame or ignition sources.

#

A

"

 

Fuel Delivery Pipe Mounting Screw Torque: 5 N.m (0.5 kgf.m, 3.5 lb-ft)

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Intruder VZR1800

ICON VARIANT Instruction Manual preview
VARIANT
Бренд: ICON Страницы: 8
hepco & becker 501546 00 01 Manual preview
501546 00 01
Бренд: hepco & becker Страницы: 5
RDMOTO CF123 Mounting Instructions preview
CF123
Бренд: RDMOTO Страницы: 2
BSA B40 VICTOR W D 1967 Workshop Manual preview
B40 VICTOR W D 1967
Бренд: BSA Страницы: 128
TVS WEGO 110 Fi Owner'S Manual preview
WEGO 110 Fi
Бренд: TVS Страницы: 60
Baja motorsports Dirt Runner 90 Owner'S Manual preview
Dirt Runner 90
Бренд: Baja motorsports Страницы: 66
DYNATEK D2K-HD2E User Instructions preview
D2K-HD2E
Бренд: DYNATEK Страницы: 8
Sundstrom SR 591 Instructions For Use Manual preview
SR 591
Бренд: Sundstrom Страницы: 68
Yamaha ET250 1980 Manual preview
ET250 1980
Бренд: Yamaha Страницы: 22
Yamaha DT50M Manual And Manual preview
DT50M
Бренд: Yamaha Страницы: 24
Yamaha E115M Owner'S Manual preview
E115M
Бренд: Yamaha Страницы: 61
Yamaha Fino 125 Manual preview
Fino 125
Бренд: Yamaha Страницы: 78
Yamaha Fazer Owner'S Manual preview
Fazer
Бренд: Yamaha Страницы: 79
Yamaha FAZER FZS1000 Owner'S Manual preview
FAZER FZS1000
Бренд: Yamaha Страницы: 94
Yamaha Fazer FZ6-S Owner'S Manual preview
Fazer FZ6-S
Бренд: Yamaha Страницы: 90
Yamaha EGO GEAR Owner'S Manual preview
EGO GEAR
Бренд: Yamaha Страницы: 86
Yamaha Fazer FZ6-SHG Owner'S Manual preview
Fazer FZ6-SHG
Бренд: Yamaha Страницы: 96
Yamaha FAZER FZ1-SA Owner'S Manual preview
FAZER FZ1-SA
Бренд: Yamaha Страницы: 96

Бренды по названию

Популярные бренды

Загрузить еще бренды