Suzuki Intruder VZR1800 Скачать руководство пользователя страница 199

Страница: 199 / 586

FI SYSTEM DIAGNOSIS 5-5

• When disconnecting and connecting the ECM, make sure to

turn OFF the ignition switch

, or electronic parts may get

damaged.

• Battery connection in reverse polarity is strictly prohibited.

Such a wrong connection will damage the components of the
FI system instantly when reverse power is applied.

• Removing any battery terminal of a running engine is strictly

prohibited.
The moment such removal is made, damaging counter elec-
tromotive force will be applied to the ECM which may result in
serious damage.

• Before measuring voltage at each terminal, check to make

sure that battery voltage is 11 V or higher. Terminal voltage
check with a low voltage battery will lead to erroneous diagno-
sis.

• Never connect any tester (voltmeter, ohmmeter, or whatever)

to the ECM when its coupler is disconnected.
Otherwise, damage to ECM may result.

• Never connect an ohmmeter to the ECM with its coupler con-

nected. If attempted, damage to ECM or sensors may result.

• Be sure to use a specified voltmeter/ohmmeter. Otherwise,

accurate measurements may not be obtained and personal
injury may result.

INCORRECT

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Intruder VZR1800

Отзывы:

Похожие инструкции для Intruder VZR1800

Бренды по названию

Популярные бренды

Suzuki Intruder VZR1800, Руководство по обслуживанию

Результаты поиска

Содержание Intruder VZR1800

Отзывы:

Похожие инструкции для Intruder VZR1800

Бренды по названию

Популярные бренды