manualshive.com logo in svg

Suzuki Intruder VZR1800, Руководство по обслуживанию


Поделиться
Скачать
background image

9-52     CHASSIS

)

$

BRAKE PAD REPLACEMENT

• Loosen the pad mounting pins 

 

1

.

• Remove the brake caliper by removing the caliper mounting

bolts 

 

2

.

• Remove the pad mounting pins 

 

1

, brake pads.

$

NOTE:
* When the brake caliper is removed, care must be used so as

not to cause stress to the brake hose. (Hang the brake caliper
on the frame with a string, etc.)

* When removing the brake pad, push the piston all the way into

the brake caliper.

• Inspect the pad mounting pins and shims for bent or damage.

If any defects are found, replace the pad mounting pins with
the new ones.

* This brake system is filled with an ethylene glycol-based DOT 4 brake fluid. Do not use mix

different types of fluid such as silicone-based or petroleum-based.

* Do not use any brake fluid taken from old, used or unsealed containers. Never reuse brake

fluid left over from the last servicing or stored for long periods.

* When storing the brake fluid, seal the container completely and keep away from children.
* When replenishing brake fluid, take care not to get dust into fluid.
* When washing brake components, use fresh brake fluid. Never use cleaning solvent.
* A contaminated brake disc or brake pad reduces braking performance. Discard contaminated

pads and clean the disc with high quality brake cleaner or neutral detergent.

Handle brake fluid with care: The fluid reacts chemically with paint, plastics, rubber materials
etc. and will damage then severely.

* Do not operate the brake lever with the pads

removed.

* Replace the brake pads as a set, otherwise braking

performance will be adversely affected.

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Intruder VZR1800

Sachs Bikes MadAss 50 Owner'S Manual preview
MadAss 50
Бренд: Sachs Bikes Страницы: 83
GBRacing BA12-6-GBR-SET Fitting Instructions preview
BA12-6-GBR-SET
Бренд: GBRacing Страницы: 2
Honda 1989 CBR1000F Owner'S Manual preview
1989 CBR1000F
Бренд: Honda Страницы: 104
Gentex CVC M9 Operation And Maintenance Manual preview
CVC M9
Бренд: Gentex Страницы: 15
PIAGGIO Liberty 50 Catalyzed 2019 Manual preview
Liberty 50 Catalyzed 2019
Бренд: PIAGGIO Страницы: 62
Honda CB TWISTER (Spanish) Manual Del Propietario preview
CB TWISTER
Бренд: Honda Страницы: 93
Sinnis motorcycles TERRAIN 125 Owner'S Manual preview
TERRAIN 125
Бренд: Sinnis motorcycles Страницы: 68
MW TOOLS 829000042 Manual preview
829000042
Бренд: MW TOOLS Страницы: 9
X-lite X-661 Safety And Instructions For Use preview
X-661
Бренд: X-lite Страницы: 96
Eastwood L6700 Instructions Manual preview
L6700
Бренд: Eastwood Страницы: 8
Yamaha MZ250 2012 Supplementary Service Manual preview
MZ250 2012
Бренд: Yamaha Страницы: 42
Yamaha Nouvo AT115C Owner'S Manual preview
Nouvo AT115C
Бренд: Yamaha Страницы: 78
Yamaha Nouv AT135 Owner'S Manual preview
Nouv AT135
Бренд: Yamaha Страницы: 84
Yamaha NMAX GPD155 2020 Owner'S Manual preview
NMAX GPD155 2020
Бренд: Yamaha Страницы: 92
Yamaha MWS150-A Owner'S Manual preview
MWS150-A
Бренд: Yamaha Страницы: 98
Yamaha NIKEN MXT850 Owner'S Manual preview
NIKEN MXT850
Бренд: Yamaha Страницы: 106
Yamaha MTM155 Owner'S Manual preview
MTM155
Бренд: Yamaha Страницы: 90
Yamaha MTN890 Owner'S Manual preview
MTN890
Бренд: Yamaha Страницы: 104

Бренды по названию

Популярные бренды

Загрузить еще бренды