Suzuki Intruder VZR1800 Скачать руководство пользователя страница 176 | Manualshive

Страница: 176 / 586

background image

DRIVELINE/AXLE 4-11

• If the backlash is not within specification, the shims (Driven

bevel gear side) must be changed and the backlash should be
re-checked until correct.
Refer to the chart for appropriate changes.

NOTE:
When changing the shims (Driven bevel gear side), measure the
thickness of old shims. Using the thickness of the old shims as a
guide, adjust the backlash by referring to the chart.

Driven bevel gear side

NOTE:
The shims (driven bevel gear side) are available as a set
(24945-26810).

TOOTH CONTACT

After bringing the backlash within specification by changing the
secondary driven bevel gear shims, it will be necessary to check
tooth contact.

• Remove the secondary gear case. (

"

4-4)

• Clean and degrease the secondary drive bevel gear teeth,

and apply a coating of machinist’s layout dye or paste to sev-
eral teeth.

• Reinstall the secondary gear case, with removed shims.
• Rotate the secondary driven bevel gear coupling several turns

in both directions.

• Remove the secondary gear case from the crankcase, and

observe the tooth contact pattern made in the dye or paste.

• Compare the tooth contact pattern to the examples as shown

in

1

,

2

and

3

.

Backlash

Shim adjustment

Under 0.03 mm (0.001 in)

Increase shim thickness

0.03 – 0.15 mm

(0.001 – 0.006 in)

Correct

Over 0.15 mm (0.006 in)

Decrease shim thickness

Part number

Shim thickness

24945-26D00-030

0.30 mm (0.012 in)

24945-26D00-035

0.35 mm (0.014 in)

24945-26D00-040

0.40 mm (0.016 in)

24945-26D00-050

0.50 mm (0.020 in)

24945-26D00-060

0.60 mm (0.024 in)

1

INCORRECT (Contact at tooth top)

2

CORRECT

«
...
174
175
176
177
178
...
»

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Intruder VZR1800

Бренд: Uclear Страницы: 2

Бренд: hepco & becker Страницы: 4

Бренд: GAS GAS Страницы: 57

Бренд: KTM Power Parts Страницы: 7

D14/4 BANTAM SUPREME D14/4 BANTAM SPORTS

Бренд: BSA Страницы: 120

Бренд: Regal Raptor Страницы: 48

Бренд: R&G Страницы: 9

Бренд: Suzuki Страницы: 526

Бренд: Wolfman Страницы: 3

MCL-4000 Series

Бренд: Dakota Digital Страницы: 3

Бренд: Megelli Страницы: 83

Бренд: Yamaha Страницы: 112

Бренд: National Cycle Страницы: 3

Бренд: Mastech Страницы: 2

Бренд: Iron Rider Страницы: 2

TORNADO Tre Novecento 900

Бренд: Benelli Страницы: 48

Бренд: Benelli Страницы: 108

Бренд: Honda Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды