Suzuki Intruder VZR1800 Скачать руководство пользователя страница 246

Страница: 246 / 586

5-52 FI SYSTEM DIAGNOSIS

Step 1 (When indicating P0110-L:)

1) Turn the ignition switch OFF.
2) Remove the fuel tank. (

6-3)

3) Check the IAT sensor coupler for loose or poor contacts.

If OK, then check the IAT sensor lead wire continuity.

4) Disconnect the IAT sensor coupler.
5) Check the continuity between Dg wire

and ground. If the

sound is not heard from the tester, the circuit condition is OK.

)

Tester knob indication: Continuity test (

(

)

6) Connect the IAT sensor coupler and turn the ignition switch

ON.

7) Measure the voltage between Dg wire

and ground.

IAT sensor output voltage: 0.15 – 4.84 V

(

Dg –

Ground)

09900-25008: Multi-circuit tester set
09900-25009: Needle pointed probe set

Tester knob indication: Voltage (

)

Are the continuity and voltage OK?

8) After repairing the trouble, clear the DTC using SDS tool.

(

5-26)

]

YES

Go to Step 2.

• Dg wire shorted to ground
• If wire is OK, go to Step 2.

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Intruder VZR1800

Отзывы:

Похожие инструкции для Intruder VZR1800

Бренды по названию

Популярные бренды

Suzuki Intruder VZR1800, Руководство по обслуживанию

Результаты поиска

Содержание Intruder VZR1800

Отзывы:

Похожие инструкции для Intruder VZR1800

Бренды по названию

Популярные бренды