manualshive.com logo in svg

Suzuki Intruder VZR1800, Руководство по обслуживанию


Поделиться
Скачать
background image

DRIVELINE/AXLE     4-23

• Remove the final gear bearing case and final driven bevel

gear, and inspect the coated teeth of the driven bevel gear.
The contact patch should be as shown at right:

• If the tooth contact pattern is incorrect, as shown in 

 

1

, a thin-

ner shim 

 

4

 is needed between the final drive bevel gear

bearing and final gear case.

• If the tooth contact pattern is incorrect, as shown in 

 

3

, a

thicker shim 

 

4

 is needed between the final drive bevel gear

bearing and final gear case.

• If the tooth contact pattern is incorrect for either reason, the

appropriate shim must be installed, and the tooth contact pat-
tern rechecked by repeating the tooth coating procedure
above.

NOTE:
If it is necessary to adjust the shim 

 

4

 thickness between final

drive bevel gear bearing and final gear case, the final gear back-
lash may change, and should be re-checked according to the
procedure outlined under the Backlash Measurement sub-sec-
tion. Both adjustments may be needed until both backlash and
tooth contact are correct.

Shims 

 

4

 specification

The shims 

 

4

 are available as a set (27445-24810).

Part No.

Shim thickness

27445-24A01-030

0.30 mm (0.012 in)

27445-24A01-035

0.35 mm (0.014 in)

27445-24A01-040

0.40 mm (0.016 in)

27445-24A01-050

0.50 mm (0.020 in)

27445-24A01-060

0.60 mm (0.024 in)

3

 INCORRECT (Contact at tooth root)

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Intruder VZR1800

KTM 690 Enduro R 2013 Repair Manual preview
690 Enduro R 2013
Бренд: KTM Страницы: 234
Victory Motorcycles 2005-2006 Hammer Service Manual preview
2005-2006 Hammer
Бренд: Victory Motorcycles Страницы: 12
Honda Z50R 1979 Manual preview
Z50R 1979
Бренд: Honda Страницы: 100
Ohlins FGR 156 Mounting Instructions preview
FGR 156
Бренд: Ohlins Страницы: 8
WangYe WY50QT-16A Manual preview
WY50QT-16A
Бренд: WangYe Страницы: 19
kellermann BL 1000 PL Installation Instructions preview
BL 1000 PL
Бренд: kellermann Страницы: 2
BMW Motorrad HP2 Megamoto Rider'S Manual preview
HP2 Megamoto
Бренд: BMW Motorrad Страницы: 146
ALPENHEAT fire PANTLINER AJ6 Manual preview
fire PANTLINER AJ6
Бренд: ALPENHEAT Страницы: 26
GAS GAS EC450 2009 User Manual preview
EC450 2009
Бренд: GAS GAS Страницы: 69
hepco & becker 503956 00 01 Manual preview
503956 00 01
Бренд: hepco & becker Страницы: 3
hepco & becker 504973 00 01 Contents preview
504973 00 01
Бренд: hepco & becker Страницы: 4
HJC FG-ST Owner'S Manual preview
FG-ST
Бренд: HJC Страницы: 9
Yamaha YZF-R6T Supplementary Service Manual preview
YZF-R6T
Бренд: Yamaha Страницы: 64
Yamaha YZFR3F Owner'S Manual preview
YZFR3F
Бренд: Yamaha Страницы: 106
Yamaha YZFR3AM 2021 Owner'S Manual preview
YZFR3AM 2021
Бренд: Yamaha Страницы: 108
Yamaha YZF600RS Owner'S Manual preview
YZF600RS
Бренд: Yamaha Страницы: 104
Yamaha YZFR1W 2007 Owner'S Manual preview
YZFR1W 2007
Бренд: Yamaha Страницы: 108
Yamaha YZF155 Owner'S Manual preview
YZF155
Бренд: Yamaha Страницы: 98

Бренды по названию

Популярные бренды

Загрузить еще бренды