manualshive.com logo in svg

Suzuki Intruder VZR1800, Руководство по обслуживанию


Поделиться
Скачать
background image

5-24     FI SYSTEM DIAGNOSIS

SELF-DIAGNOSTIC PROCEDURES

NOTE:
* Don’t disconnect couplers from the ECM, the battery cable

from the battery, ECM ground wire harness from the engine or
main fuse before confirming the malfunction code (self-diag-
nostic trouble code) stored in memory. Such disconnection will
erase the memorized information in ECM memory.

* Malfunction code stored in ECM memory can be checked by

the special tool.

* Before checking malfunction code, read SELF-DIAGNOSIS

FUNCTION “USER MODE and DEALER MODE” (

#

5-17 and

5-18) carefully to have good understanding as to what functions
are available and how to use it.

* Be sure to read “PRECAUTIONS IN SERVICING” (

#

5-3)

before inspection and observe what is written there.

• Remove the left frame lower side cover. (

#

3-6)

• Connect the special tool to the dealer mode coupler at the wir-

ing harness, and start the engine or crank the engine for more
than 4 seconds.

• Turn the special tool’s switch ON and check the malfunction

code to determine the malfunction part.

!

09930-82720: Mode select switch

SELF-DIAGNOSIS RESET PROCEDURE

• After repairing the trouble, turn OFF the ignition switch and

turn ON again.

• If the malfunction code indicates (C00), the malfunction is

cleared.

• Disconnect the special tool from the dealer mode coupler.

NOTE:
* Even though the malfunction code (C00) is indicated, the previ-

ous malfunction history code still remains stored in the ECM.
Therefore, erase the history code memorized in the ECM using
SDS.

* The malfunction code is memorized in the ECM also when the

wire coupler of any sensor is disconnected. Therefore, when a
wire coupler has been disconnected at the time of diagnosis,
erase the stored malfunction history code using SDS.

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Intruder VZR1800

Razor Indian eFTR Mini 2021 Owner'S Manual preview
Indian eFTR Mini 2021
Бренд: Razor Страницы: 20
Yukon Trail Puma 200 Owner'S Manual preview
Puma 200
Бренд: Yukon Trail Страницы: 21
Honda Z50R 1979 Manual preview
Z50R 1979
Бренд: Honda Страницы: 100
GAS GAS TXT PRO - PART LIST 2005 Parts List preview
TXT PRO - PART LIST 2005
Бренд: GAS GAS Страницы: 38
Shark Heritage Manual preview
Heritage
Бренд: Shark Страницы: 80
Wunderlich 35520-002 Manual preview
35520-002
Бренд: Wunderlich Страницы: 2
R&G FI0090BK Fitting Instructions preview
FI0090BK
Бренд: R&G Страницы: 2
R&G FI0089BK Fitting Instructions preview
FI0089BK
Бренд: R&G Страницы: 2
R&G FI0126BK Fitting Instructions preview
FI0126BK
Бренд: R&G Страницы: 4
R&G FI0078BK Fitting Instructions preview
FI0078BK
Бренд: R&G Страницы: 4
R&G FI0083 Fitting Instructions Manual preview
FI0083
Бренд: R&G Страницы: 7
Palm 11480 Manual preview
11480
Бренд: Palm Страницы: 14
Shift Power Full Race Unit Installation Manual preview
Full Race Unit
Бренд: Shift Power Страницы: 7
Shift Power C-K11 Installation Manual preview
C-K11
Бренд: Shift Power Страницы: 7
Wunderlich 8166235 User Manual preview
8166235
Бренд: Wunderlich Страницы: 1
Wunderlich 31962-002 Fitting Instruction preview
31962-002
Бренд: Wunderlich Страницы: 2
Wunderlich 43520-222 Manual preview
43520-222
Бренд: Wunderlich Страницы: 5
Wunderlich 35835-002 Manual preview
35835-002
Бренд: Wunderlich Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды