Supero SuperServer 5012B-6 Скачать руководство пользователя страница 71

Страница: 71 / 112

Chapter 6: Advanced Chassis Setup

6-7

IDE Drive Installation (5012B-E only)

Mounting an IDE drive in a drive carrier

Like SCSI drives, IDE drives are also mounted in drive carriers to simplify

their installation and removal from the chassis. These carriers also help

promote proper airflow. For this reason, even empty carriers without IDE

drives installed must remain in the chassis. To add a new IDE drive,

install a drive into the carrier with the printed circuit board side toward

the carrier so that the mounting holes align with those in the carrier.

Secure the drive to the carrier with the four screws.

Installing/removing IDE drives

The two IDE drive bays are located in the front of the chassis, making

them easily accessible for installation and removal. The IDE drives are

not hot-swap units, meaning system power must be turned off before

installing and/or removing them. To install or remove a drive, first power

down the system and then remove the top cover of the chassis. Un-

screw the retention screw at the top center of the drive, then push the

drive carrier out from the back until you can grasp and pull it out through

the front of the chassis (see Figure 6-6). Reverse this procedure when

installing a drive carrier, making sure you screw in the retention screw.

Replace the top cover when finished.

SCSI Power Cables

SCSI power cables should be routed so that they do not block the airflow

through the chassis. There is a 4-pin connector for the power cables.

SCA Backplane

The SCSI drives plug into an SCA backplane that provides power, SCSI ID

and bus termination. A RAID controller can be used with the SCA backplane

to provide data security. The operating system you use must have RAID

support to enable the hot-swap capability of the SCSI drives. The SCA

SCSI backplane is already preconfigured, so there are no jumpers or

switches present on it.

Содержание SuperServer 5012B-6

















































































































Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды

Supero SuperServer 5012B-6, Руководство пользователя

Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды