Supero SuperServer 5012B-6 Скачать руководство пользователя страница 60

Страница: 60 / 112

5-22

UPER

ERVER 5012B-6/5012B-E Manual

Watchdog Enable/Disable

Jumper JP39 allows you to enable

or disable the Watchdog feature.

The normal (default) position is

closed to disable the watchdog

timer and enable the speaker. See

the table on the right for jumper

settings.

Jumper

Position

O pen

Closed

Definition

Disabled
Enabled

W atchdog

Enable/Disable Jum per

Settings (JP39)

Keyboard Wake-Up

The JPWAKE jumper is used to-

gether with the Keyboard Wake-

Up function in BIOS. Enable both

the jumper and the BIOS setting to

allow the system to be woken up

by depressing a key on the key-

board. See the table on the right

for jumper settings.

Note:

Your power supply must

meet ATX specification 2.01 or

h i g h e r a n d s u p p l y 7 2 0 m A o f

standby power to use this fea-

ture.

Jumper

Position

1-2
2-3

Definition

Disabled

Enabled

Keyboard W ake-Up

Jum per Settings

(JPW AKE)

Overheat Fan Enable/Disable

JP38 allows you to enable or disable

the overheat (thermal) fan. When

enabled, the fan will operate con-

tinuously. When disabled, it will op-

erate only when a predefined tem-

perature threshold has been ex-

ceeded. See the table on the right

for jumper settings.

Jumper

Position

Open

Closed

Definition

Disabled

Enabled

T hermal Fan

Enable/Disable

Jumper Settings (JP38)

Содержание SuperServer 5012B-6

















































































































Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды

Supero SuperServer 5012B-6, Руководство пользователя

Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды