Supero SuperServer 5012B-6 Скачать руководство пользователя страница 98

Страница: 98 / 112

7-24

UPER

ERVER 5012B-6/5012B-E Manual

Boot Other Device

If enabled, this option enables the BIOS to load the OS from another device

rather than the ones that have been specified as the first, second and third

boot up devices. The settings are "

Enabled

" and "Disabled".

Virus Warning

This item allows the user to choose the VIRUS Warning feature for IDE Hard

Drive Disk boot sector protection. If this function is enabled and someone

attempts to write data into this area, the BIOS will display a warning

message and an alarm will sound. The settings are "Enabled", and

Disabled

Boot Up Floppy Seek

Set this option to "Enabled" to allow the BIOS to test floppy drives to

determine whether they have 40 tracks or 80 tracks. The settings are

"Enabled" or "

Disabled

Содержание SuperServer 5012B-6

















































































































Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды

Supero SuperServer 5012B-6, Руководство пользователя

Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды