Supero SuperServer 5012B-6 Скачать руководство пользователя страница 61

Страница: 61 / 112

Chapter 5: Advanced Motherboard Setup

5-23

5-10 Parallel Port/Floppy/Hard Disk and SCSI

Connections

Be aware of the following when connecting the floppy and hard disk drive

cables:

•

A red mark on a wire typically designates the location of pin 1.

•

A single floppy disk drive ribbon cable has 34 wires and two connectors

to provide for two floppy disk drives. The connector with the twisted

wires always connects to drive A, and the connector that does not have

twisted wires always connects to drive B.

Parallel Port Connector

The parallel port is located on J35.

See the table below for pin defini-

tions.

Pin Number

Function

Strobe-

Data Bit 0

Data Bit 1

Data Bit 2

Data Bit 3

Data Bit 4

Data Bit 5

Data Bit 6

Data Bit 7

ACK

BUSY

SLCT

Pin Number

Function

Auto Feed-

Error-

Init-

SLCT IN-

G ND

Parallel (Printer) Port Pin Definitio ns

(J35)

Содержание SuperServer 5012B-6

















































































































Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды

Supero SuperServer 5012B-6, Руководство пользователя

Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды