Supero SuperServer 5012B-6 Скачать руководство пользователя страница 33

Страница: 33 / 112

Chapter 3: System Interface

3-3

Power:

Indicates power is being supplied to the system's power

supply units. This LED should normally be illuminated when the system is

operating.

3-4

SCSI Drive Carrier LEDs (5012B-6 only)

Each SCSI drive carrier has two LEDs.

Green:

When illuminated, the green LED on the front of the SCSI drive

carrier indicates drive activity. A connection to the SCSI SCA backplane

enables this LED to blink on and off when that particular drive is being

accessed.

Red:

A SAF-TE compliant backplane is needed to activate the red LED

to indicate a drive failure. (A SAF-TE compliant SCSI backplane is optional

on the 5012B-6.) If one of the SCSI drives fail, you should be notified by

your system management software. Please refer to Section 6-4 for instruc-

tions on replacing failed SCSI drives.

3-5

Power Supply Switch

An on/off switch is located on the back of the power supply. This switch

should normally be on at all times. Turning this switch to the off position

removes both the main and standby power from the system, as opposed to

the power button located on the control panel on the front of the chassis.

3-6

Motherboard LEDs

PW (Power_On) LED

There is one PW (Power_on) LED on the motherboard. When illuminated, it

indicates that system power is present on the motherboard. This LED is

located in the corner of the P4SBR/P4SBE near the DIMM2 slot.

Содержание SuperServer 5012B-6

















































































































Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды

Supero SuperServer 5012B-6, Руководство пользователя

Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды