Supero SuperServer 5012B-6 Скачать руководство пользователя страница 11

Страница: 11 / 112

Chapter 1

Introduction

1-1

Overview

The Supermicro SuperServer 5012B-6/5012B-E is a high-end single proces-

sor, 1U rackmount server that features some of the most advanced technol-

ogy currently available. The SuperServer 5012B-6/5012B-E is comprised of

two main subsystems: the SC810 1U rackmount chassis and the P4SBR (for

5012B-6) or P4SBE (for 5012B-E) single 478-pin Pentium 4 microPGA pro-

cessor mainboard. Please refer to our web site for information on operat-

ing systems that have been certified for use with the SuperServer 5012B-

6/5012B-E (www.supermicro.com).

In addition to the mainboard and chassis, various hardware components

may have been included with your SuperServer 5012B-6/5012B-E, as listed

below.

One CPU heatsink

One (1) 1.44" floppy drive

One (1) slim CD-ROM drive

One (1) SCA SCSI backplane (5012B-6 only)

Two (2) SCA SCSI drive carriers (5012B-6 only)

SCSI Accessories (5012B-6 only):

One (1) internal 68-pin Ultra160 SCSI cable for SCA SCSI backplane

One (1) set of SCSI driver diskettes

One (1) SCSI manual

One (1) 5V 32-bit, 33 MHz PCI slot riser card

Rackmount hardware (with screws):

Two (2) rack rail assemblies

Six (6) brackets for mounting the rack rails in a rack/telco rack

Chapter 1: Introduction

1-1

Содержание SuperServer 5012B-6

















































































































Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды

Supero SuperServer 5012B-6, Руководство пользователя

Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды