Supero SuperServer 5012B-6 Скачать руководство пользователя страница 3

Страница: 3 / 112

Preface

About This Manual

This manual is written for professional system integrators and PC techni-

cians. It provides information for the installation and use of the Super-

Server 5012B-6/5012B-E. Installation and maintainance should be per-

formed by experienced technicians only.

The SuperServer 5012B-6/5012B-E is a high-end single processor 1U

rackmount server based on the SC810 1U rackmount server chassis and

either the Super P4SBR (for the 5012B-6) or the P4SBE (for the 5012B-E)

mainboard. The P4SBR/P4SBE mainboard supports single Intel

Pentium

processors up to 2.60 GHz in 478-pin microPGA sockets.

Manual Organization

Chapter 1: Introduction

The first chapter provides a checklist of the main components included with

the server system and describes the main features of the Super P4SBR and

P4SBE mainboards and the SC810 chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer

5012B-6/5012B-E into a rack and check out the server configuration prior to

powering up the system. If your server was ordered without the proces-

sor and memory components, this chapter will refer you to the appropriate

sections of the manual for their installation.

Chapter 3: System Interface

Refer to this chapter for details on the system interface, which includes the

functions and information provided by the control panel on the chassis as

well as other LEDs located throughout the system.

iii

Preface

Содержание SuperServer 5012B-6

















































































































Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды

Supero SuperServer 5012B-6, Руководство пользователя

Результаты поиска

Содержание SuperServer 5012B-6

Отзывы:

Похожие инструкции для SuperServer 5012B-6

Бренды по названию

Популярные бренды