Supero SuperServer 1025C-M3 Скачать руководство пользователя страница 55

Страница: 55 / 110

Chapter 5: Advanced Serverboard Setup

5-19

Watch Dog

JWD enables the Watch Dog function,

a system monitor that takes action

when a software application freezes

the system. Jumping pins 1-2 will have

WD reboot the system if a program

freezes. Jumping pins 2-3 will gener-

ate a non-maskable interrupt for the

program that has frozen. See the table

on the right for jumper settings. Watch

Dog must also be enabled in BIOS.

Note:

when Watch Dog is enabled, the user

must write their own application software to

disable the Watch Dog Timer.

Watch Dog

Jumper Settings (JWD)

Jumper Setting Defi nition

Pins 1-2

Reset

Pins 2-3

NMI

Open

Disabled

LAN1/LAN2 Enable/Disable

Change the setting of jumper JPL1 to

enable or disable the LAN1 port and

JPL2 to enable or disable the LAN2

port on the serverboard. See the table

on the right for jumper settings. The

default setting is enabled.

LAN1/2 Enable/Disable

Jumper Settings (JPL1/2)

Jumper Setting Defi nition

Pins 1-2

Enabled

Pins 2-3

Disabled

SAS Enable/Disable

Jumper Settings (JPA1)

Jumper Settings Defi nition

Pins 1-2

Enabled

Pins 2-3

Disabled

SAS Enable/Disable

JPA1 allows you to enable or disable

the SAS controller. The default posi-

tion is on pins 1 and 2 to enable SAS.

See the table on the right for jumper

settings.

SAS RAID Select

JPA2 allows you to select between

SR RAID, which is the default and

enables SAS RAID, or IT RAID, which

treats SAS drives as non-RAID drives

and requires a fi rmware fl ash. See the

table on the right for jumper settings.

Contact Supermicro tech support if

using the IT RAID setting.

SAS RAID Select

Jumper Settings (JPA2)

Jumper Setting Defi nition

Open

IT RAID

Closed

SR RAID

Note:

SR = Software RAID IT = Integrate

Target mode

Содержание SuperServer 1025C-M3















































































































Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды

Supero SuperServer 1025C-M3, Руководство пользователя

Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды