Supero SuperServer 1025C-M3 Скачать руководство пользователя страница 11

Страница: 11 / 110

Chapter 1

Introduction

1-1 Overview

The SuperServer 1025C-M3 is a dual processor server comprised of two main

subsystems: the SC113MTQ-560CB 1U rackmount chassis and the X7DCL-3

serverboard. Please refer to our web site for information on operating systems that

have been certifi ed for use with the 1025C-M3 (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components may have

been included with the 1025C-M3, as listed below.

Two (2) CPU heatsinks (SNK-P0017)

•

One (1) slim DVD-ROM drive (DVM-TEAC-824B)

•

SAS/SATA

Accessories:

•

Eight (8) SAS/SATA hard drive carriers (MCP-220-00047-0B)

One (1) internal SAS/SATA backplane (BPN-SAS-113TQ)

Two (2) SAS/SATA cable sets (CBL-0186L)

Two (2) SGPIO cables (CBL-0157L)

•

One (1) PCI-E x8 riser card (CSE-RR1U-E8)

•

One (1) front side USB/COM port tray [(CSE-PT-40(B)]

•

Four (4) 4-cm high-performance fans (FAN-0061L4)

•

Rackmount hardware with screws (CSE-PT51L)

•

One (1) CD containing drivers and utilities

•

SuperServer 1025C-M3 User's Manual

•

Note: "B" indicates part is available in black.

Chapter 1: Introduction

1-1

Содержание SuperServer 1025C-M3















































































































Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды

Supero SuperServer 1025C-M3, Руководство пользователя

Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды