Supero SuperServer 1025C-M3 Скачать руководство пользователя страница 29

Страница: 29 / 110

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel to keep you constantly informed of the

overall status of the system as well as the three buttons described below.

3-2 Control Panel Buttons

There are two buttons located on the front of the chassis: a reset button and a

power on/off button.

Reset

Use the reset button to reboot the system.

Power

This is the main power button, which is used to apply or turn off the main system

power. Turning off system power with this button removes the main power but keeps

standby power supplied to the system.

UID

A UID (unit identifi er) button is included on the SC113MTQ-560CB chassis but it

is not functional.

Содержание SuperServer 1025C-M3















































































































Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды

Supero SuperServer 1025C-M3, Руководство пользователя

Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды