Supero SuperServer 1025C-M3 Скачать руководство пользователя страница 13

Страница: 13 / 110

Chapter 1: Introduction

1-3

PCI Expansion Slots

The X7DCL-3 has two PCI-Express x8 slots, one PCI-Express x4 slot (in a x8 slot)

and three 32-bit, 33 MHz (5V) PCI slots. In the 1025C-M3 server confi guration, a

PCI-E riser card (CSE-RR1U-E8) has been installed to support a single PCI-Ex-

press add-on card.

Ethernet Ports

The X7DCL-3 has two network controllers integrated into the chipset to support two

Gigabit LAN ports (100/1000Base-T/1000BaseTX, RJ45 output).

Onboard Controllers/Ports

An onboard IDE controller supports Ultra ATA 100 hard drives or ATAPI devices.

Onboard I/O backpanel ports include one COM port, a VGA port, two USB ports,

PS/2 mouse and keyboard ports and two Gigabit LAN (NIC) ports.

Other Features

Other onboard features that promote system health include voltage monitors, a

chassis intrusion header, auto-switching voltage regulators, chassis and CPU

overheat sensors, virus protection and BIOS rescue.

Содержание SuperServer 1025C-M3















































































































Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды

Supero SuperServer 1025C-M3, Руководство пользователя

Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды