Supero SuperServer 1025C-M3 Скачать руководство пользователя страница 89

Страница: 89 / 110

Chapter 7: BIOS

7-17

IPMI (Available only when an IPMI card is installed.)

0IP0M0000I Specification Version:

This item displays the current IPMI

Version.

Firmware Version:

This item displays the current Firmware Version.

System Event Logging000

Select Enabled to enable IPMI Event Logging. When this function is set to Disabled,

the system will continue to log events received via system interface. The options

are

Enabled

and Disabled.

Clear System Event Logging

Enabling this function to force the BIOS to clear the system event logs during the

next cold boot. The options are Enabled and

Disabled

Existing Event Log Number

This item displays the number of the existing event log.

Event Log Control

System Firmware Progress

Enabling this function to log POST progress. The options are Enabled and

Disabled

BIOS POST Errors

Enabling this function to log POST errors. The options are Enabled and

Disabled

BIOS POST Watch Dog

Set to Enabled to enable POST Watch Dog. The options are Enabled and

Disabled

Содержание SuperServer 1025C-M3















































































































Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды

Supero SuperServer 1025C-M3, Руководство пользователя

Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды