Supero SuperServer 1025C-M3 Скачать руководство пользователя страница 51

Страница: 51 / 110

Chapter 5: Advanced Serverboard Setup

5-15

Wake-On-LAN

The Wake-On-LAN header is des-

ignated JWOL on the serverboard.

See the table on the right for pin

defi nitions. You must enable the LAN

Wake-Up setting in BIOS to use this

function. (You must also have a LAN

card with a Wake-On-LAN connector

and cable to use this feature.)

Universal Serial Bus (USB)

There are two Universal Serial Bus

ports located on the I/O panel and

four additional USB headers located

on the serverboard. The headers,

labeled USB2/3 and USB4/5, can be

used to provide front side USB access

(cables not included). See the tables

on the right for pin defi nitions.

Wake-On-LAN

Pin Defi nitions

(JWOL)

Pin# Defi nition

+5V Standby

Ground

Wake-up

USB Ports Pin

Defi nitions (USB0/1)

Pin# Defi nitions

+5V

PO-

PO+

Ground

N/A

USB Headers

Pin Defi nitions (USB2/3, USB4/5)

USB2/4
Pin # Defi nition

USB3/5
Pin # Defi nition

+5V

PO-

PO+

Ground

Key

No connection

Wake-On-Ring

The Wake-On-Ring header is des-

ignated JWOR. This function allows

your computer to receive and be

"awakened" by an incoming call when

in the suspend state. See the table on

the right for pin defi nitions. You must

also have a WOR card and cable to

use this feature.

Wake-On-Ring

Pin Defi nitions

(JWOR)

Pin# Defi nition

Ground (Black)

Wake-up

Содержание SuperServer 1025C-M3















































































































Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды

Supero SuperServer 1025C-M3, Руководство пользователя

Результаты поиска

Содержание SuperServer 1025C-M3

Отзывы:

Похожие инструкции для SuperServer 1025C-M3

Бренды по названию

Популярные бренды