Supermicro SUPERSERVER 6013A-T Скачать руководство пользователя страница 86

Страница: 86 / 126

7-18

UPER

ERVER 6013A-T User's Manual

Hardware Health Event Monitoring

This feature allows the BIOS to display Hardware Health Event Monitoring

Results. The user cannot modify the results. The results are for display

only.

USB Configuration

This feature allows the user to configure USB settings.

USB Functions

This feature allows the user to set USB functions. The options are

"Disabled", "2 USB Ports", "4 USB Ports",

"6 USB Ports"

"8 USB Ports".

Legacy USB Support

Select "Enabled" to enable the support for USB Legacy. The options are

"Disabled" and "

Enabled

USB 2.0 Controller

Select "Enabled" to activate the USB 2.0 Controller. The options are

"Disabled" and "

Enabled

USB 2.0 Controller Mode

This feature allows the user to select the USB 2.0 Controller Mode. The

options are "Full Speed", and "

Hi Speed

Stop EHCI HC in OHCI Handover

This feature allows the BIOS to disable the EHCI Host Controller during OHCI

OS Handover Call. This is needed for the operating system that does not

support EHCI Host Controller. The options are

"Enabled"

and "Disabled".

USB Mass Storage Device Configuration

This feature allows the user to configure USB Mass Storage Device set-

tings.

USB Mass Storage Reset Delay

This feature allows the user to set the reset delay for USB Mass

Storage. The options are "10 Sec", "

20 Sec

", "30 Sec" and "40 Sec".

Содержание SUPERSERVER 6013A-T































































































































Результаты поиска

Содержание SUPERSERVER 6013A-T

Отзывы:

Похожие инструкции для SUPERSERVER 6013A-T

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 6013A-T, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 6013A-T

Отзывы:

Похожие инструкции для SUPERSERVER 6013A-T

Бренды по названию

Популярные бренды