Supermicro SUPERSERVER 6013A-T Скачать руководство пользователя страница 32

Страница: 32 / 126

3-2

UPER

ERVER 6013A-T User's Manual

3-3

Control Panel LEDs

The control panel located on the front of the SC811T-350 chassis has five

LEDs. These LEDs provide you with critical information related to different

parts of the system. This section explains what each LED indicates when

illuminated and any corrective action you may need to take.

OVERHEAT:

Indicates an overheat condition in the chassis. This may

be caused by cables obstructing the airflow in the system, or the ambient

room temperature being too warm. You should also check to make sure

that the chassis cover is installed and that all fans are present and operat-

ing normally. Finally, check the air seals for damage. The air seals are

located under the blower fan and beneath the frame cross section that

separates the drive bay area from the motherboard area of the chassis.

NIC2:

Indicates network activity on LAN2 (Gb port) when flashing .

NIC1:

Indicates network activity on LAN1 (Mb port) when flashing.

HDD:

Indicates IDE channel activity. On the SuperServer 6013A-T this

light indicates SATA and CD-ROM drive activity when flashing.

NIC2

NIC1

Содержание SUPERSERVER 6013A-T































































































































Результаты поиска

Содержание SUPERSERVER 6013A-T

Отзывы:

Похожие инструкции для SUPERSERVER 6013A-T

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 6013A-T, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 6013A-T

Отзывы:

Похожие инструкции для SUPERSERVER 6013A-T

Бренды по названию

Популярные бренды