Supermicro SUPERSERVER 6013A-T Скачать руководство пользователя страница 45

Страница: 45 / 126

Chapter 5: Advanced Motherboard Setup

5-7

Figure 5-3. 604-pin Socket: Empty and with Processor Installed

IMPORTANT!

Please note that special, new silver heatsink retention clips must

be used with all Xeon 533 MHz FSB (front side bus) 604-pin processors.

These new retention clips have “604P” clearly marked on them. Using the old

clips will not keep the proper amount of pressure applied and may cause the

processor to overheat. You should not use these new retention clips with

Xeon 400 MHz FSB processors (even if the CPU socket is 604-pin) as they will

too tight and damage the CPU socket.

Figure 5-4a. Retention Clips (left: 603-pin, right: 604-pin)

Содержание SUPERSERVER 6013A-T































































































































Результаты поиска

Содержание SUPERSERVER 6013A-T

Отзывы:

Похожие инструкции для SUPERSERVER 6013A-T

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 6013A-T, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 6013A-T

Отзывы:

Похожие инструкции для SUPERSERVER 6013A-T

Бренды по названию

Популярные бренды