Supermicro SUPERSERVER 6013A-T Скачать руководство пользователя страница 11

Страница: 11 / 126

Chapter 1

Introduction

1-1

Overview

The Supermicro SuperServer 6013A-T is an economical dual Xeon processor, 1U

rackmount server with state-of-the-art features. The 6013A-T is comprised of two

main subsystems: the SC811T-350 chassis and the X5DPA-TGM+ motherboard.

Please refer to our web site for information on operating systems that have been

certified for use with the 6013A-T (www.supermicro.com).

In addition to the motherboard and chassis, various hardware components may

have been included with your SuperServer 6013A-T, as listed below.

Two (2) 1U CPU heatsinks (SNK-039)

Four (4) heatsink retention clips (for either 604 or 603-pin CPUs)

Two (2) CPU mounting plates and retention modules (SKT-120)

One (1) 3.5" floppy drive

One (1) slim CD-ROM drive

Serial ATA (SATA) Accessories:

One (1) SATA backplane (CSE-SATA-810)

Two (2) SATA cables (CBL-0058)

One (1) SATA LED cable (CBL-0056)

Two (2) SATA drive carriers (CSE-PT10)

One (1) 5V 32-bit, 33 MHz PCI slot riser card (CSE-RR32-1U)

Rackmount hardware (with screws):

Two (2) rack rail assemblies

Six (6) brackets for mounting the rack rails in a rack/telco rack

One (1) CD containing drivers and utilities

Chapter 1: Introduction

1-1

Содержание SUPERSERVER 6013A-T































































































































Результаты поиска

Содержание SUPERSERVER 6013A-T

Отзывы:

Похожие инструкции для SUPERSERVER 6013A-T

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 6013A-T, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 6013A-T

Отзывы:

Похожие инструкции для SUPERSERVER 6013A-T

Бренды по названию

Популярные бренды